Rancang Bangun Infusion Device Analyzer Dilengkapi Tampilan Suhu dan Kelembapan Ruangan Berbasis Arduino
Keywords:
Arduino Uno, DHT22, IDA, MPX5700AP, OptocouplerAbstract
Infusion Device Analyzer is a tool for testing the performance of an infusion pump and Syringe Pump. This tool measures flow and occlusion provided by the infusion pump and syringe pump. So a tool is needed to calibrate the infusion pump and syringe pump according to applicable standards so that swelling does not occur in the patient. The design of this calibration tool can also be used as student learning material so that students can understand and comprehend the working principles of the Infusion Device Analyzer. This tool is made using the Arduino Uno control system and there is an occlusion and flow measurement display along with room temperature and humidity which will be displayed on the Nextiton 4'3 Inch LCD. Accompanied by an optocoupler sensor as a liquid flow detector and an MPX5700AP sensor as a liquid pressure detector which is equipped with a DHT22 sensor as a room temperature and humidity meter. This calibrator tool is also equipped with a solenoid valve to regulate the entry of fluid to be measured between flow or occlusion measurements. The function test results show that the flowrate measurement of 10 is 12ml/h, 50 is 54ml/h, 100 is 105ml/h while the occlusion with a rate of 100 is 2.66 psi and the tolerance value for the parameters is appropriate. Therefore, the tool created is close to the desired plan and can be used as a suitable comparison of whether a Syringe Pump or Infusion Pump tool is suitable after repairs or during maintenance. This tool can also be used in learning for students to understand the parts of the working principle of this tool.
References
Alfian, R., & Maulana, D. (2020). Rancang bangun sistem kalibrasi tekanan darah digital berbasis mikrokontroler Arduino Uno. Jurnal Teknik Elektromedik Indonesia, 2(2), 45–52.
Andriani, T., & Yusuf, M. (2022). Pengujian akurasi alat ukur suhu digital berbasis mikrokontroler Arduino Nano. Jurnal Teknologi dan Sistem Informasi, 10(1), 33–40.
Fitriyah, N., & Santoso, A. (2021). Desain sistem monitoring suhu dan kelembaban berbasis DHT22 menggunakan Arduino Uno. Jurnal Elektronika dan Otomasi, 9(2), 115–122.
Hafidz, R., & Widiyanto, P. (2020). Penerapan metode PID pada sistem kontrol suhu alat medis menggunakan sensor LM35. Jurnal Teknik Elektro dan Komputer, 5(3), 201–209.
Hidayat, M., & Pratama, R. (2021). Pengembangan sistem monitoring suhu dan tekanan alat medis menggunakan sensor digital. Jurnal Instrumentasi dan Otomasi Medik, 5(1), 27–35.
Iskandar, A., & Rahmawati, N. (2019). Sistem pemantauan infus otomatis berbasis mikrokontroler untuk peningkatan keselamatan pasien. Jurnal Rekayasa Elektronika dan Informatika, 4(3), 99–106.
Kusnandar, D., & Siregar, F. (2022). Implementasi Internet of Things (IoT) untuk pemantauan alat medis di rumah sakit. Jurnal Teknologi Kesehatan, 8(1), 11–19. https://doi.org/10.31227/osf.io/9khts
Lestari, F., & Suryana, D. (2020). Kalibrasi alat ukur suhu dan tekanan untuk peralatan medis menggunakan sistem otomatis berbasis Arduino. Jurnal Sains dan Teknologi Terapan, 18(2), 120–127.
Naufal, M. R., & Putra, E. P. (2023). Pengembangan sistem kalibrasi digital untuk alat ukur tekanan darah berbasis Arduino. Jurnal Aplikasi Teknologi dan Instrumentasi, 2(2), 47–55.
Naufal, R., & Hartanto, P. (2023). Desain sistem kalibrasi alat infus pump berbasis mikrokontroler ESP32. Jurnal Teknologi dan Riset Elektromedik, 3(2), 54–61.
Pradana, I., & Rahayu, L. (2021). Sistem pemantauan suhu ruang steril rumah sakit menggunakan IoT berbasis NodeMCU. Jurnal Teknologi Informasi dan Komputer, 7(4), 289–296.
Putri, A. D., & Wibowo, Y. (2021). Analisis efektivitas perawatan preventif peralatan medis di rumah sakit pemerintah. Jurnal Kesehatan dan Keselamatan Kerja, 10(2), 78–85.
Setiawan, H., & Kurniawan, D. (2020). Pengujian performa alat infus otomatis berbasis Arduino dan sensor ultrasonik. Jurnal Teknologi Kesehatan, 6(2), 73–81.
Wulandari, S., & Nugroho, A. (2022). Rancang bangun sistem kalibrasi alat kesehatan berbasis sensor digital dan Arduino. Jurnal Ilmu Teknik dan Kesehatan, 6(4), 134–142.
Yulianto, B., & Fitria, S. (2019). Implementasi sistem kalibrasi suhu berbasis mikrokontroler untuk laboratorium klinik. Jurnal Inovasi Teknologi dan Sains, 4(1), 56–6
